Every "ST" series camera is supplied with a desiccant plug installed in the camera and a spare "dummy" that is used to plug the CCD chamber while baking the actual desiccant plug.
|
2" replacement nosepiece for STL Series CCD cameras.
|
This cable is used to directly power the STL camera from a 12VDC source using a cigarette lighter plug.
|
This cable extends the cord from the power "brick" to the camera by approximately 8 feet (~2.44m). The standard cable that comes with the power supply is about 6 feet (~1.83m) long so this heavy-duty extension cable brings the total length to about 14 feet (~4.27m). It is custom made with heavy gauge conductor for minimum voltage loss. The wire bundle is contained in a braided shell for added flexibility.
|
Replacement back plate assembly with rack handles for the ST-7/8/9/10/2000 camera (assembly includes plate, fan, LED and wiring harness with connector).
|
The relay adapter box converts the ST-7/8/9/10/2000 electronic relays to mechanical relays.
|
For mounting Nikon lenses on the camera with a CFW5-8300 filter wheel. FW5-8300 Filter Wheel illustrated with optional Nikon lens adapter.
|
ST-8300 lens adapter for use with a filter wheel (FW5-8300 or FW8-8300).
|
This 12VDC submersible water pump was added as an accessory for the larger STL series cameras. However, if you are operating an ST-7/8/9/10/2000 camera in the field or any place where there is no convenient 110VAC supply, then it may be adapted for use with an ST series camera by using two pieces of step down tubing from the camera to the smaller tubing supplied with the 12VDC pump.
|
This accessory is a more robust replacement of the dual relay ribbon cable. The Telescope Port Splitter is designed to reduce CFW8A and AO-7 cable failure over time due to flexing. It also adds an extra RJ-11 outlet and four red LED indicator lights to give a visual confirmation of the camera's relay activity.
|
This adapter mates the ST-7/8/9/10/2000 cameras with popular 35mm camera lenses for wide field imaging. Adapters are available for Pentax bayonet, Olympus, Canon FD, or Nikon.The CLA-7 cannot be used with a filter wheel, but it can be used with the male-to-male t-thread adapter in place of the threaded barrel to hold a 1.25" filter behind the camera lens.
|
This adapter mates the ST-7/8/9/10/2000 cameras with popular 35mm camera lenses for wide field imaging. Adapters are available for Pentax bayonet, Olympus, Canon FD, or Nikon.The CLA-7 cannot be used with a filter wheel, but it can be used with the male-to-male t-thread adapter in place of the threaded barrel to hold a 1.25" filter behind the camera lens.
|
Provides the required 5VDC and 12VDC to the camera from typical line voltages found around the world. It has an on/off switch and green LED showing power is on to the camera. A separate cord is available with regional plug for N. America and Europe / Asia. This is the supply that is included with all current models of ST-7/8/9/10/2000 cameras. It is compatible with all all past models as well.
|
110V power supply (Wall Transformer), ordered without camera
|
CLA7-8300 for mounting Nikon or Canon FD 35mm lenses on the ST-8300 camera body without filter wheel.
|
Research Grade RGB Filters w/IR blocking for CFW8/CFW10 - specify your desired color at time of order. Price is for each filter.
|
Adapts the AO-L to work with any dual sensor ST-7/8/9/10/2000 USB camera alone or with CFW9 or CFW10 Filter Wheel.
|
This adapter mates the STL series cameras with Nikon 35mm camera lenses for wide field imaging.
|
Fits the CFW-10 filter wheel allowing the use of most Nikon 35mm lenses with an ST camera + CFW-10 combination. This adapter will only work when the CFW-10 is attached to an ST-7/8/9/10/2000 camera by replacing the camera face plate. In other words, it will not work with the CFW-10-SA stand alone version. Due to the limited backfocus requirements the locking pin is also removed on this adapter.
|
FR-237 and E-Finder Assembly
|