This adapter is supplied with all "ST" series cameras. It plugs into the 9 pin "AO/CFW/SCOPE" port on an ST-7/8/9/10/2000 camera and accepts an RJ-11 to RJ-11 Tracking Cable that connects the camera to your telescope drive's autoguider ("CCD") port. This adapter plug is not required when using a CFW8A.
|
This ribbon type extension cable with additional ports is also supplied with an AO-7 so that an "ST" series camera can control a CFW8A, telescope drive and AO-7 all at the same time. This cable is provided with every AO-7 as a convenience, however for permanent use the more robust Port Splitter accessory should be used.
|
RJ-11 to RJ-11 modular 6-conductor cable used for guiding. Supplied with all ST Series cameras.
|
This cap is machined from solid aluminum and black anodized.It is threaded to fit the 2.1" aperture of STL cameras to prevent dust from entering the filter wheel cover when the 2" nosepiece is not attached.
|
SBIG Tripod Mounting Block for the STV.
|
SBIG Accessory Lens for ST-7/8/9/10/2000 CCD Cameras. This inexpensive test lens allows the user to become familiar with CCD Camera operation and software in the comfort of his home, without a telescope. If one just sets the camera-lens combination outside on the gournd looking up, images of the constellations can be taken up to 10 sec long before elongation occurs.
|
12v power cord designed specifically for the ST402 camera. Has a cigarette lighter plug as well as clips for easy attachment to your 12v source.
|
This 10 foot (~3 m) cable extends the cord from the wall transformer to the camera with secure locking connectors at both ends. It is custom made with sufficiently heavy gauge conductor for minimum voltage loss.
|
T-Thread to C-Mount Adapter
|
12VDC power cable for the ST-5C, ST-237/A and STV. This cable will also work with the older cooling booster accessory that required a separate 12VDC power supply.
|
Replacement custom cut foam for ST-7/8/9/10/2000 case - with cutout for camera +CFW10 attached.
|
For a more secure attachment of your camera to a Schmidt-Cassegrain telescope (or any scope using typical SCT threads) replace your nosepiece with this adapter. One end screws into the female t-threads on the front of the camera or filter wheel, and the other end screws onto the rear cell threads typically found on most commercial Schmidt-Cassegrain telescopes. A matching hard plastic dust cap screws over the t-thread end if the camera is removed for any period of time.
|
These T-thread nosepieces screw into the female t-threads on ST cameras. All ST cameras include at least one nosepiece. The nosepiece is threaded to accept filters and notched for extra security in the event the retaining screw comes loose slighlty during the night.
|
These T-thread nosepieces screw into the female t-threads on ST cameras. All ST cameras include at least one nosepiece. The nosepiece is threaded to accept filters and notched for extra security in the event the retaining screw comes loose slighlty during the night.
|
This low-cost hard case is blow-molded black plastic with a custom cut foam insert for the ST-402ME camera and its power supply, plus extra room for cables, nose-piece, filters, etc.
|
CLA-7 camera mount section only.
|
The Baader UV / IR blocking filter is essentially a luminance filter. It is included with ST-2000XCM color cameras to improve the color balance of the single shot color CCD by blocking the near IR light. It is shown here along side the optional T-ring with filter threads for use on any ST cameras. It can be placed behind a camera lens adapter and used to block the out of focus near IR light that causes stars to look bloated with using a typical 35mm camera lens to shoot wide field images.
|
SBIG 12VDC Power Cable with Cigarette Lighter Adapter for the Research Class CCD Cameras.
|
This lens adapter comes in two parts: T-to-C Thread adapter ring and a C-thread to 35mm lens adapter. Both are necessary for using a 35mm camera lens with the ST-402/1603/3200 cameras. However, if you have C-mount lenses, only the T-to-C Thread adapter ring is required. 35mm camera lenses supported are Pentax bayonet, Canon FD (manual focus only), Olympus and Nikon.
|
This lens adapter comes in two parts: T-to-C Thread adapter ring and a C-thread to 35mm lens adapter. Both are necessary for using a 35mm camera lens with the ST-402/1603/3200 cameras. However, if you have C-mount lenses, only the T-to-C Thread adapter ring is required. 35mm camera lenses supported are Pentax bayonet, Canon FD (manual focus only), Olympus and Nikon.
|