To attach the Pyxis to the COM (RS-232 serial) port of a computer requires a special cable. These cables are flat 6-wire stranded with RJ-12 modular connectors on both ends. They are typically refered to as reverse cables since each pin number on one connector is connected to the same number on the other end.
|
To attach the Pyxis to the COM (RS-232 serial) port of a computer requires a special cable. These cables are flat 6-wire stranded with RJ-12 modular connectors on both ends. They are typically refered to as reverse cables since each pin number on one connector is connected to the same number on the other end.
|
6-Foot Cable, SBIG ST-4/5/6 CCD Camera to Hand Controller, DB-9 to RJ-11
|
Allows PC communications with the TCF-S Focuser (stk. no. 17670) using any 9-pin serial port. An RJ-12 Reverse Cable is required for proper operation. See stock no. 17671 through 17675).
|
Optec Y-splitter cable for 12 VDC power supply, 2.5mm plug, 3-ft length. One regulated power supply can be used to supply power to two Optec devices.
|
IFW filter wheel replacement O-ring, 3-pack.
|
Optec 6-foot power supply extender cable.
|
Optec 6-ft. Serial cable for SSP photometers, DB-9 F/F. RS-232 cable for connection between PC DB-9 serial port and DB-9 port on SSP photometers.
|
12-Foot Cable, SBIG ST-4/5/6 CCD Camera to Hand Controller, DB-9 to RJ-11
|
To attach the Pyxis to the COM (RS-232 serial) port of a computer requires a special cable. These cables are flat 6-wire stranded with RJ-12 modular connectors on both ends. They are typically refered to as reverse cables since each pin number on one connector is connected to the same number on the other end.
|
Six-foot cable substitutes for standard 20" cable supplied with stk. #17660 or #17670.
|
Optec Model WIS PC Communications Cable. 20’ ft. long serial connection cable for PC configuration of the Precipitation and Wind Sensor Modules.
|
L mounting bracket with 1/4 -20 thread. This L shaped bracket sllows the Pyxis to be mounted on a side support or optical bench.
|
Optec 12 VDC Universal Power Supply, input range 90-264V AC, 12-watt output. For use with most Optec devices including TCF, TCF-S, MAXfilter 2”, IFW, SSP-3, SSP-5, PFE.
|
Optec 5 VDC Power Supply, input range 100-120V AC input, 15-watt output. Use with SSP-4 only.
|
Violet light rejection filter, mounted in 48mm threaded cell. 420nm cutoff. (Now included with WideField and WideField 2” telecompressors.) Glass filters mounted in 48mm threaded cell for insertion into 2” eyepiece or MAXfield/WideField lens assembly.
|
#8 Pale Yellow, mounted in 48mm threaded cell. 495nm cutoff. (Now included with MAXfield and MAXfield 2” telecompressors.)Glass filters mounted in 48mm threaded cell for insertion into 2” eyepiece or MAXfield/WideField lens assembly.
|
#21 Orange, mounted in 48mm threaded cell. Glass filters mounted in 48mm threaded cell for insertion into 2” eyepiece or MAXfield/WideField lens assembly.
|
#23A Light Red, mounted in 48mm threaded cell. Glass filters mounted in 48mm threaded cell for insertion into 2” eyepiece or MAXfield/WideField lens assembly.
|
#47B Blue, mounted in 48mm threaded cell. Glass filters mounted in 48mm threaded cell for insertion into 2” eyepiece or MAXfield/WideField lens assembly.
|